说明:收录25万 73个行业的国家标准 支持批量下载
文库搜索
切换导航
文件分类
频道
文件分类
批量下载
ICS _21. 220. 10 J 18 GB 中华人民共和国国家标准 GB/T 10412--2002 代替GB/T10412—1989 普通和窄V带轮(基准宽度制) Grooved pulleys for classical and narrow V-belts(system based on datum width) (ISO 4183:1995 Belt drivesClassical and narrow V-belts -Grooved pulleys(system based on datum width),MOD) 2002-10-11发布 2003-05-01实施 中华人民共和国 发布 国家质量监督检验检疫总局 GB/T 10412—2002 前 言 本标准修改采用ISO4183:1995《带传动普通和窄V带带轮(基准宽度制)》。 本标准是GB/T10412一1989《普通V带轮》的修订版。修订后的标准注重通用性、互换性,删除了 原标准中轮幅结构、轮缘和轮毂等规定;改变了圆跳动公差的测量位置;增加了多槽带轮任意两个轮槽 基准直径间最大偏差的规定。 本标准的附录A是资料性附录。 本标准自实施之日起,同时代替GB/T104121989。 本标准由中国机械工业联合会提出。 本标准由机械科学研究院归口。 本标准起草单位:机械科学研究院。 本标准主要起草人:秦书安。 本标准于1989年首次发布,2002年第一次修订。
GB-T 10412-2002 普通和窄V带轮(基准宽度制)
文档预览
中文文档
9 页
50 下载
1000 浏览
0 评论
309 收藏
3.0分
赞助2元下载(无需注册)
温馨提示:本文档共9页,可预览 3 页,如浏览全部内容或当前文档出现乱码,可开通会员下载原始文档
下载文档到电脑,方便使用
赞助2元下载
本文档由 人生无常 于
2024-06-01 03:11:39
上传分享
举报
下载
原文档
(9.7 MB)
分享
友情链接
ISO 23936-2 2011 Petroleum, petrochemical and natural gas industries — Non-metallic materials in contact with media related to oil and gas production — Part 2 Elastomers.pdf
ISO PAS 11585 2023 Road vehicles — Partial driving automation — Technical chara.pdf
ISO 13966 1998 Thermoplastics pipes and fittings — Nominal ring stiffnesses.pdf
ISO 5610-1 2014 Tool holders with rectangular shank for indexable inserts Part 1 General survey correlation and determination of dimensions.pdf
ISO 20535 2019 Footwear — Test method for insoles and insocks — Dimensional change after cycle of wetting and drying.pdf
ISO 19013-2 2016 Rubber hoses and tubing for fuel circuits for internal combustion engines — Specification — Part 2 Gasoline fuels.pdf
ISO 23865 2021 Non-destructive testing Ultrasonic testing General use of full matrix capture-total focusing technique (FMC-TFM) and related technologies.pdf
ISO 109-1982Textile machinery. Working widths of weaving machines first edition.pdf
ISO TS 21346 2021 Nanotechnologies — Characterization of individualized cellulose nanofibril.pdf
ISO 19013-1 2019 Rubber hoses and tubing for fuel circuits for internal combustion engines — Specification — Part 1 Diesel fuels.pdf
GB-T 20334-2006 G系列和Rp系列管螺纹磨牙丝锥的螺纹尺寸公差.pdf
GB-T 33314-2023 腐蚀控制工程全生命周期 通用要求.pdf
GB-T 33719-2017 标准中融入可持续性的指南.pdf
GB-T 14791-2013 螺纹 术语.pdf
GB-T 21737-2008 为消费者提供商品和服务的购买信息.pdf
GB-T 3668.3-1983 组合机床通用部件 回转工作台和回转工作台用多边形中间底座尺寸.pdf
GB-T 9089.2-2008 户外严酷条件下的电气设施 第2部分 一般防护要求.pdf
GB-T 10190-2012 电子设备用固定电容器 第16部分 分规范 金属化聚丙烯膜介质直流固定电容器.pdf
GB-T 18052-2000 套管、油管和管线管螺纹的测量和检验方法.pdf
GB-T 9352-2008 塑料 热塑性塑料材料试样的压塑.pdf
1
/
3
9
评价文档
赞助2元 点击下载(9.7 MB)
回到顶部
×
微信扫码支付
2
元 自动下载
官方客服微信:siduwenku
支付 完成后 如未跳转 点击这里 下载
站内资源均来自网友分享或网络收集整理,若无意中侵犯到您的权利,敬请联系我们
微信(点击查看客服)
,我们将及时删除相关资源。